|
Product Details:
Payment & Shipping Terms:
|
| Shelf Life: | 2 Years | Materials: | Pure Epoxy |
|---|---|---|---|
| Capacity: | 650ml | Mixing Ratio: | 1:1 |
| Color: | Grey Or Red | Weight: | 1200g |
| Initial Curing: | 30 Mins Under 25 Degree Celsius | Tensile Strength: | 55KN |
| High Light: | rebar anchoring epoxy,cement anchor epoxy |
||
650ml Tow Components Resin Epoxy Anchor Adhesive For Thread Rods Installation
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing glue,
Chemical anchoring system used for anchoring and rebar connections in concrete.
Strong, Versatile Epoxy Anchor Adhesives For Threaded Rod, Rebar
Item #: FixingChor165
Capacity: 650ml
Materials: Epoxy
Mixing Ratio: 1:1
650ml Tow Components Resin Epoxy Anchor Adhesive For Thread Rods Installation
A resin epoxy (RE) anchor adhesive is a two part chemical anchor that is designed to harden slowly
so you have longer working times for applications such as deep embedments
Applied in one single action this resin will produce a high performance, strong fixing with exceptionally
high chemical resistance.
Solvent free, made of modified epoxy resin, two part high performance anchoring adhesive.
Advantages:
High load capacities
Non-sagging, even overhead handling,
Crack and non-cracked concrete
Styrene free
Can use in damped area
High stability
Low odour
Good Smelling
Non contraction after harden
No transportation restrictions
High bond strength,
Can be applied in severe environments
With molecular structural combining the Hydrophilic group and hydrophobic group
Can be used and keep high performance in any environment of moisture, hot and still
works even if the surface of hole is smooth.
Good elongation property
No breaking under high stressing.
repristinate after stressing.
APPLICATION
-Fixing handrails,reinforcement bars, steel constructions, machines, wood constructions, especially suitable for big diameter rebar and rods.
-Suitable to resist loads in cracked or uncracked concrete base material for cases where anchor design theory and criteria applies.
-Bonding threaded rod and reinforcing bar into hardened concrete.
-Can be installed in a wide range of base material temperatures.
-Medium&Heavy duty load applications.
-Ideal for indoor usage.
-High durability.
2 Main Performance
| Testing project | Condition | Index | ||
| Gel Performance (According to China National Standard GB50728-2011) | ||||
| Split Tensile Strength (MPa) | Under (23±2)℃, (50±5)%RH, tested by loading speed of 2mm/min | ≥8.5 | ||
| Flexural Strength (MPa) |
≥50 (no fragment damage) |
|||
| Compressive Strength (MPa) | ≥60 | |||
| Bonding Capacity (According to China National Standard GB50728-2011) | ||||
| Steel-Steel Tensile Shear Strength (MPa) | (23±2)℃ (50±5)%RH | ≥10 | ||
| Bond strength of Ribbed steel bar (or screw) with concrete under constrain drawing condition | (23±2)℃ (50±5)%RH | C30,Ф25,L=150mm | ≥11 | |
| C60,Ф25,L=150mm | ≥17 | |||
| Steel to Steel T-peeling strength (mm) | (23±2)℃,(50±5)%RH | ≤25 | ||
| Non-volatile contents | (105±2)℃,(180±5)min | ≥99% | ||
| Ageing resistance to heat and humidity 90d | ||||
| Reduction rate of tensile strengths | Under normal room temperature | ≤12% | ||
| (According to China National Standard JGJ145-2013) | ||||
| Tensile Strength (after high temperature welding) |
Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm |
55.1N, 57.0N, 54.8N | ||
3 Technical Data
Anchoring Adhesive used with thread rod
| Thread Rod Dia |
C30 Concrete |
M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | 12 | 14 | 18 | 24 | 28 | |
| Depth (mm) | 90 | 110 | 145 | 180 | 220 | |
| Damage Pulling force KN | Grade 5.8 Steel | 29 | 42.2 | 78.5 | 122.5 | 254.5 |
| Grade 8.8 Steel / A4 SS | 36.8 | 52.9 | 94.1 | 147.0 | 211.7 | |
| Damage Cutting force KN | Grade 5.8 Steel | 17.4 | 25.3 | 47.1 | 73.5 | 105.9 |
| Grade 8.8 Steel | `27.8 | 40.5 | 75.3 | 117.6 | 169.4 | |
| Designed Pulling force KN | 12.0 | 17.02 | 30.6 | 52.4 | 75.2 | |
| Designed Cutting Force KN | Grade 5.8 Steel | 12.2 | 17.6 | 32.9 | 51.5 | 74.1 |
| Grade 8.8 Steel | 18.6 | 27.0 | 50.2 | 78.4 | 113.0 | |
| Holes for each | 54 | 25 | 8 | 5 | 3 |
ATTENTION
-Do not install anchors when substrate temperature is less than 0°C.
-Do not install anchors when the temperature is less than 10°C.
-If the cartridge is not finished, please clean the opening, then put the plug back and cap tightly.
-It can be used again in the future by replacing the static mixer.
-Please ensure hole is properly cleaned. Hole may be damp but must be free from water.
-Do not dilute mortar with any solvents and/or other chemicals.
-Please use Xinchor nozzles, other nozzles may cause ineffective mixing
and reduce the properties of the mortar.
-At temperatures below 10°C should be warmed or stored in temperatures
of 10-30°C for 24hours prior to use to improve product flow and cure.
-If the gelling time expires, please use a new static mixer.
-Do not cut or shorten nozzles.
-Not suitable for use in diamond cored holes without roughening.
-Please ensure spiral mixer in static nozzles.
-Do not install into uncured concrete.
Curing time:
| Operation and Curing time | |||||
| Temperarure ℃ | -5 | 0 | 10 | 20 | ≥30 |
| Operation time (min) | 60 | 45 | 30 | 25 | 20 |
| Curing time (h) | 72 | 48 | 24 | 12 | 6 |
Consumption Chart (holes per cartridge)
| Anchor Rod dia. | M10 | M12 | M16 | M20 | M24 |
| Drilling Dia.(mm) | 12 | 14 | 18 | 24 | 28 |
| Depth (mm) | 90 | 110 | 145 | 180 | 220 |
| Each usage | 8ml | 13ml | 28ml | 62ml | 103ml |
| 360ml | 45 | 27 | |||
| 390ml | 48 | 30 | 14 | 6 | 3 |
| 585ml | 73 | 45 | 20 | 9 | 5 |
| 650ml | 81 | 50 | 23 | 10 | 6 |
|
Quality & Service : our priority has always been providing our clients with great quality products and superior customer service with instant response. |
|
Quick Lead : Time We're dedicated to providing the quickest turnaround times and work very Hard to ensure that all of your deadlines are met. |
|
Unbeatable Prices: We continuously strive to find ways of reducing our production costs, and passing the savings over to you! |
|
Brand Awareness: The goal of any strong brand is achieve a level of awareness that instills the idea of quality and value into all of your potential customers. |
|
Special Offers: In order to maintain our competitive advantage, we are constantly running special offers on our prices and services. Contact our sales team to see how we can help you save a lot of money. |
Our Product Lines:
- Carbon Fiber Reinforcement System: XQ-CFC 300gsm, 200gsm 600gsm fabric and adhesives XQ-XW
- Steel Bonding System: XQ-GZ Epoxy grouting adhesives, XQ-JGN Plate bonding Adhesives
- Crack Repairing System: XQ-GF Crack grouting adhesives, XQ-FF crack seal adhesives
- Chemical Anchoring 390ml(3:1), 585ml(3:1), 650ml(1:1),
Our History:
15 years from 2000,45 employees, 5000m2 plant, ISO9001 approved,
Our Quality
All passed China National Standard lab testing, and be similar to CE and other countries standards
Our main product series:
-- Steel bonding reinforcement system
XQ-GZ Grouting epoxy adhesive
XQ-FB edge sealing adhesive
XQ-JGN structural epoxy adhesive
-- Chemical Anchor series
Pure Epoxy Adhesive 585ml (3:1) 360ml (5:1) 390ml(3:1)
-- Carbon fiber reinforcement system,
XQ-XW carbon fiber epoxy adhesive
XQ-XB concrete surface leveling epoxy adhesive
XQ-CFC carbon fiber fabric 12K unidirectional 200gsm-600gsm
-- Concrete repair system
XQ-GF crack grouting adhesive
XQ-FF crack sealing adhesive
Contact Person: Colin Mao
Tel: 86-13336183725
