Payment & Shipping Terms:
|Color:||Grey Or Red||Weight:||1200g|
|Initial Curing:||30 Mins Under 25 Degree Celsius||Mixing Ratio:||1:1|
|Tensile Strength:||55KN||Shelf Life:||2 Years|
epoxy anchoring system,
cement anchor epoxy
650ml Large Pack Styrene Free Epoxy Anchor Adhesive For Building Rehablitation
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing glue,
Chemical anchoring system used for anchoring and rebar connections in concrete.
Strong, Versatile Epoxy Anchor Adhesives For Threaded Rod, Rebar
Item #: FixingChor165
Mixing Ratio: 1:1
650ml Styrene Free Epoxy Anchor Adhesive For Building Rehablitation
Pure Epoxy 1:1 resin is a high performance, two components pure epoxy resin system. Applied in one
single action this resin will produce a high performance, strong fixing with exceptionally high chemical resistance.
Solvent-free, epoxy resin based, two part high performance anchoring adhesive.
Can use in damp area
High load capacities
Non-sagging, even overhead
Non contraction after harden
No transportation restrictions
High bonding strength,
Can be applied in severe environment
With molecular structure combining the Hydrophilic group and hydrophobic group
Can operate and keep high performance in any environment of moisture, hot and still
works even if the surface of hole is smooth.
Good elongation property
No breaking under high stressing.
repristinate after stressing.
-Fixing machines, handrails, steel constructions, wood constructions, reinforcement bars, especially suitable for big diameter rebar and rods.
-Suitable to resist loads in cracked or uncracked concrete base material for cases where anchor design theory and criteria applies.
-Bonding threaded rod and reinforcing bar into hardened concrete.
-Can be installed in a wide range of base material temperatures.
-Medium&Heavy duty load applications.
-Ideal for indoor usage.
2 Main Performance
|Gel Performance (According to China National Standard GB50728-2011)|
|Split Tensile Strength (MPa)||Under (23±2)℃, (50±5)%RH, tested by loading speed of 2mm/min||≥8.5|
|Flexural Strength (MPa)||
(no fragment damage)
|Compressive Strength (MPa)||≥60|
|Bonding Capacity (According to China National Standard GB50728-2011)|
|Steel-Steel Tensile Shear Strength (MPa)||(23±2)℃ (50±5)%RH||≥10|
|Bonding strength of Ribbed steel bar (or screw) with concrete under constrain drawing condition||(23±2)℃ (50±5)%RH||C30,Ф25,L=150mm||≥11|
|Steel-Steel T-peeling strength (mm)||(23±2)℃,(50±5)%RH||≤25|
|Ageing resistance to heat and humidity 90d|
|Reduction rate of tensile strength||Under normal room temperature||≤12%|
|(According to China National Standard JGJ145-2013)|
|Tensile Strength (after high temperature welding)||
Dia12 Grade II steel, C30 concrete
Hole dia.16mm, Depth: 150mm
|55.1N, 57.0N, 54.8N|
3 Technical Data
Anchoring Adhesive used with thread rod
|Thread Rod Dia||
|Damage Pulling force KN||Grade 5.8 Steel||29||42.2||78.5||122.5||254.5|
|Grade 8.8 Steel / A4 SS||36.8||52.9||94.1||147.0||211.7|
|Damage Cutting force KN||Grade 5.8 Steel||17.4||25.3||47.1||73.5||105.9|
|Grade 8.8 Steel||`27.8||40.5||75.3||117.6||169.4|
|Designed Pulling force KN||12.0||17.02||30.6||52.4||75.2|
|Designed Cutting Force KN||Grade 5.8 Steel||12.2||17.6||32.9||51.5||74.1|
|Grade 8.8 Steel||18.6||27.0||50.2||78.4||113.0|
|Holes for each||54||25||8||5||3|
-Do not install anchors when substrate temperature is less than 0°C.
-Do not install anchors when the temperature is less than 10°C.
-If the cartridge is not finished, please clean the opening, then put the plug back and cap tightly.
-It can be used again in the future by replacing the static mixer.
-Please ensure hole is properly cleaned. Hole may be damp but must be free from water.
-Do not dilute mortar with any solvents and/or other chemicals.
-Not suitable for use in diamond cored holes without roughening.
-Please ensure spiral mixer in nozzles.
-Do not install into uncured concrete.
-Please use Xinchor nozzles, other nozzles may cause ineffective mixing
and reduce the properties of the mortar.
-At temperatures below 10°C should be warmed or stored in temperatures
of 10-30°C for 24hours prior to use to improve product flow and cure.
-If the gelling time expires, please use a new static mixer.
-Do not cut or shorten nozzles.
|Operation and Curing time|
|Operation time (min)||60||45||30||25||20|
|Curing time (h)||72||48||24||12||6|
Consumption Chart (holes per cartridge)
|Anchor Rod dia.||M10||M12||M16||M20||M24|
Quality & Service :
our priority has always been providing our clients with great quality products and superior customer service.
Quick Lead :
Time We're dedicated to providing the quickest turnaround times and work very Hard to ensure that all of your deadlines are met.
We continuously strive to find ways of reducing our production costs, and passing the savings Over to you!
The goal of any strong brand is achieve a level of awareness that instills the idea of quality and value into all of your potential customers.
In order to maintain our competitive edge, we are constantly running special offers on our promotion gifts, consumer goods, and design services. Contact our sales team to see how we can help you save a lot of money.
Our Product Lines:
- Carbon Fiber Reinforcement System: XQ-CFC 300gsm, 200gsm fabric and adhesives XQ-XW
- Steel Bonding System: XQ-GZ Epoxy grouting adhesives, XQ-JGN Plate bonding Adhesives
- Crack Repairing System: XQ-GF Crack grouting adhesives, XQ-FF crack seal adhesives
- Chemical Anchoring 390ml(3:1), 585ml(3:1), 650ml(1:1),
15 years from 2000,40 employees, 5000m2 plant, ISO9001 approved,
All passed China National Standard lab testing, and be similar to CE and other countries standards
Our main product series:
-- Steel bonding reinforcement system
XQ-GZ Grouting epoxy adhesive
XQ-FB edge sealing adhesive
XQ-JGN structural epoxy adhesive
-- Chemical Anchor series
Pure Epoxy Adhesive 585ml (3:1) 360ml (5:1) 390ml(3:1)
-- Carbon fiber reinforcement system,
XQ-XW carbon fiber epoxy adhesive
XQ-XB concrete surface leveling epoxy adhesive
XQ-CFC carbon fiber fabric 12K unidirectional 200gsm-600gsm
-- Concrete repair system
XQ-GF crack grouting adhesive
XQ-FF crack sealing adhesive
Contact Person: Colin Mao