|
Product Details:
Payment & Shipping Terms:
|
| Resin Type: | Modified Pure Epoxy | Mix Ratio: | 2:1 |
|---|---|---|---|
| Application: | Railway Installation | Capacity: | 450ml |
| Tensile Strength: | 55KN | T-peeling Strengt: | Less Than 25mm |
| Tensile Shear Strength: | Above 10Mpa | Rebar Size: | Dia. 10-32 |
| High Light: | epoxy anchoring system,rebar anchoring epoxy |
||
450ml 2:1 Side By Side Cartridge Epoxy Anchor Adhesive For Railway installation
Chemical anchor adhesive, epoxy injection mortar, Chemical fixing glue,
Chemical anchoring system used for anchoring and rebar connections in concrete.
Item #: FixingChor145
Capacity: 450ml
Materials: Epoxy
Mixing Ratio: 2:1
Product Description:
450ml 2:1 Side By Side Cartridge Epoxy Anchor Adhesive For Railway installation is
a high performance, two components pure epoxy chemcial anchor adhesive. strong fixing with
exceptionally high chemcial resistance.Applied in one single action this resin will produce a high performance,
PRODUCT FEATURES
-Longer working time.
-Styrene free.
-Designed for use with threaded rod and reinforcing bar hardware elements.
-Orange color can be easily detected or monitored.
-Wide temperature range(5°C~+40°c)
-High grip force, high adhesive force.
-Special application to diamond drilled holes and large bore diameter.
-The product ingredient is odorless and non-toxic.
Characteristics
Suitable for medium loads and non-critical applications.
Used for studs and relatively small diameter rebar. ⋅
Fixings in concrete, wood, or other high strength materials.
Good durability formulation, resistance to chemicals.
Fast working times for early loading in time sensitive applications.
Use in extremely cold environments and fixings holes.
|
Testing project |
Condition |
Index |
||
|
Gel Performance (According to China National Standard GB50728-2011) |
||||
|
Splitting Tensile Strength (MPa) |
Under (23±2)℃,(50±5)%RH, tested by loading speed of 2mm/min |
≥8.5 |
||
|
Flexural Strength (MPa) |
≥50 (no fragment damage) |
|||
|
Compressive Strength (MPa) |
≥60 |
|||
|
Bonding Capacity (According to China National Standard GB50728-2011) |
||||
|
Steel-Steel Tensile Shear Strength (MPa) |
(23±2)℃,(50±5)%RH |
≥10 |
||
|
Bonding strength of Ribbed steel bar (or screw) with concrete under constrain drawing condition |
(23±2)℃ (50±5)%RH |
C30,Ф25,L=150mm |
≥11 |
|
|
C60,Ф25,L=150mm |
≥17 |
|||
|
Steel-Steel T-peeling strength (mm) |
(23±2)℃,(50±5)%RH |
≤25 |
||
|
Non-volatile content |
(105±2)℃,(180±5)min |
≥99% |
||
|
Ageing resistance to heat and humidity 90d |
||||
|
Reduction rate of tensile strength |
Under normal room temperature |
≤12% |
||
|
(According to China National Standard JGJ145-2013) |
||||
|
Tensile Strength (after high temperature welding) |
Dia12 Grade II steel, C30 concrete Hole dia.16mm, Depth: 150mm |
55.1N, 57.0N, 54.8N |
||
Approved for anchorings in
Concrete, cracked and non-cracked Applications
Rebar planting in concrete structures.
Railway or express way modification works
Structure reinforcement
Curtain wall installing
Bridge modification works
Keel fixing in out wall
ATTENTION
-If the gelling time expires, please use a new static mixer.
-Do not cut or shorten nozzles.
-It can be used again in the future by replacing the static mixer.
-Please ensure hole is properly cleaned. Hole may be damp but must be free from water.
-Do not install anchors when substrate temperature is less than 0°C.
-Do not install anchors when the temperature is less than 10°C.
-If the cartridge is not finished, please clean the opening, then put the plug back and cap tightly.
-At temperatures below 10°C should be warmed or stored in temperatures
of 10-30°C for 24hours prior to use to improve product flow and cure.
Contact Person: Colin Mao
Tel: 86-13336183725
